click2electro

Forum Replies Created

Ero fault in fuji FRENIC MEGA drive

Cause: Positioning control error comes when an excessive positioning deviation has occurred when the servo-lock function was activated. This fault typically occurs when the drive is operating in a clo...

In forum Fuji FRENIC-MEGA (G2), Eco, Lift & FVR-Micro Drive

2 days ago
dba fault in fuji FRENIC MEGA drive

Cause: Braking transistor error comes when a braking transistor error is detected. The "dba" fault specifically means the drive has detected a malfunction within the braking transistor circuit. dba f...

In forum Fuji FRENIC-MEGA (G2), Eco, Lift & FVR-Micro Drive

2 days ago
cof fault in fuji FRENIC MEGA drive

Cause: PID feedback wire break comes when the PID feedback wire is broken. This alarm is triggered when the feedback signal used in PID control becomes invalid, such as when the feedback signal wire b...

In forum Fuji FRENIC-MEGA (G2), Eco, Lift & FVR-Micro Drive

2 days ago
err fault in fuji FRENIC MEGA drive

Cause: Mock alarm comes when the "STOP" + "Function/Data" keys were held down for more than 5 seconds. To escape from this alarm state, press "PRG/RESET" the key.

In forum Fuji FRENIC-MEGA (G2), Eco, Lift & FVR-Micro Drive

2 days ago
nrb fault in fuji FRENIC MEGA drive

Cause: NTC wire break error comes when a wire break is found in the NTC thermistor detection circuit. An NTC thermistor's resistance decreases as its temperature increases. A "wire break" suggests an ...

In forum Fuji FRENIC-MEGA (G2), Eco, Lift & FVR-Micro Drive

2 days ago
ere fault in fuji FRENIC MEGA drive

Cause: Speed mismatch or excessive speed deviation comes when an excessive deviation appears between the speed command and the detected speed. ere fault in fuji FRENIC MEGA drive indicates Speed misma...

In forum Fuji FRENIC-MEGA (G2), Eco, Lift & FVR-Micro Drive

2 days ago
erh fault in fuji FRENIC MEGA drive

Cause: Hardware error comes when the LSI on the power printed circuit board malfunctions. Or, the fuse blew inside the inverter. erh fault in fuji FRENIC MEGA drive indicates Hardware error. This mean...

In forum Fuji FRENIC-MEGA (G2), Eco, Lift & FVR-Micro Drive

3 days ago
erf fault in fuji FRENIC MEGA drive

Cause: Data saving error during undervoltage comes when the inverter failed to save data such as the frequency commands and PID commands (which are specified through the keypad), or the output frequen...

In forum Fuji FRENIC-MEGA (G2), Eco, Lift & FVR-Micro Drive

3 days ago
erp fault in fuji FRENIC MEGA drive

Cause: RS-485 communications error (COM port 2) comes when a communications error occurred during RS-485 communications. This means the drive is unable to establish or maintain reliable communication ...

In forum Fuji FRENIC-MEGA (G2), Eco, Lift & FVR-Micro Drive

3 days ago
er8 fault in fuji FRENIC MEGA drive

Cause: RS-485 communications error (COM port 1) comes when a communications error occurred during RS-485 communications. This means the drive is unable to establish or maintain reliable communication ...

In forum Fuji FRENIC-MEGA (G2), Eco, Lift & FVR-Micro Drive

3 days ago
er7 fault in fuji FRENIC MEGA drive

Cause: Tuning error comes when auto-tuning failed. This fault specifically occurs when the drive's motor autotuning (also known as auto-tuning or auto-setting) process fails or encounters an issue. ...

In forum Fuji FRENIC-MEGA (G2), Eco, Lift & FVR-Micro Drive

3 days ago
er6 fault in fuji FRENIC MEGA drive

Cause: Operation protection comes when an error has occurred due to an operation incorrect to the operation method. This is a general fault code that indicates the drive's internal protection function...

In forum Fuji FRENIC-MEGA (G2), Eco, Lift & FVR-Micro Drive

3 days ago
er5 fault in fuji FRENIC MEGA drive

Cause: Option error comes when an error detected by the option card. An option error means that the specific functionality or integrity of an installed option card is compromised. The card might be fa...

In forum Fuji FRENIC-MEGA (G2), Eco, Lift & FVR-Micro Drive

3 days ago
er4 fault in fuji FRENIC MEGA drive

Cause: Option communications error comes when a communications error occurred between the option card and the inverter. er4 fault in fuji FRENIC MEGA drive indicates Option communications error. This...

In forum Fuji FRENIC-MEGA (G2), Eco, Lift & FVR-Micro Drive

3 days ago
er3 fault in fuji FRENIC MEGA drive

Cause: CPU error comes when the central processing unit (CPU) – the "brain" of the inverter – has detected an internal error or malfunction. This prevents the drive from executing its program and cont...

In forum Fuji FRENIC-MEGA (G2), Eco, Lift & FVR-Micro Drive

3 days ago
Page 1 / 1331