click2electro

Forum Replies Created

E42.04 fault in inovance IS580 drive

E42.04 fault in inovance IS580 drive indicates BUS card fault. This means there is a problem detected in the communication BUS card/module inside the drive that handles CAN communication. Internal el...

In forum Inovance CP700 – Air compressor & IS580 – Injunction Molding Drive

2 days ago
E42.03 fault in inovance IS580 drive

E42.03 fault in inovance IS580 drive indicates "the communication never gets online". This means the drive’s communication device (e.g., CAN, Modbus, Ethernet) never establishes an online connection w...

In forum Inovance CP700 – Air compressor & IS580 – Injunction Molding Drive

2 days ago
E42.02 fault in inovance IS580 drive

E42.02 fault in inovance IS580 drive indicates CAN communication fault - "Commnunication gets interfered". This means the drive detects that the CAN bus communication is being interrupted or lost. Ch...

In forum Inovance CP700 – Air compressor & IS580 – Injunction Molding Drive

2 days ago
E42.01 fault in inovance IS580 drive

E42.01 fault in inovance IS580 drive indicates CAN communication fault - "Communication gets interrupted". This means the drive detects that the CAN bus communication is being interrupted or lost. Ch...

In forum Inovance CP700 – Air compressor & IS580 – Injunction Molding Drive

2 days ago
E40.00 fault in inovance IS580 drive

E40.00 fault in inovance IS580 drive indicates Overcurrent multi prevention fault. This means the drive has detected a current level exceeding its set threshold multiple times or continuously, trigger...

In forum Inovance CP700 – Air compressor & IS580 – Injunction Molding Drive

2 days ago
E27.00 fault in inovance IS580 drive

E27.00 fault in inovance IS580 drive indicates "Business time out". This means a communication or operation timeout related to the drive’s “business” (control or data exchange) process — basically, th...

In forum Inovance CP700 – Air compressor & IS580 – Injunction Molding Drive

2 days ago
E26.00 fault in inovance IS580 drive

E26.00 fault on the Inovance IS580 drive indicates a Timeout Fault. This means the drive has detected that a certain operation or communication process has taken too long and exceeded its expected tim...

In forum Inovance CP700 – Air compressor & IS580 – Injunction Molding Drive

2 days ago
E24.00 fault in inovance IS580 drive

Cause: Output phase to phase short-circuit fault comes when internal motor failure where two windings are shorted together or faulty motor cable. E24.00 fault in inovance IS580 drive indicates Output ...

In forum Inovance CP700 – Air compressor & IS580 – Injunction Molding Drive

2 days ago
E23.09 fault in inovance IS580 drive

Cause: Motor ground fault comes when motor suddenly starts running at high speed upon power-up, and the drive detects a ground fault. E23.09 fault on an Inovance IS580 drive is a Motor Ground Fault, j...

In forum Inovance CP700 – Air compressor & IS580 – Injunction Molding Drive

2 days ago
E23.00 fault in inovance IS580 drive

Cause : Motor ground fault comes when one or more of the motor phases (U/V/W) are shorted to earth/ground. E23.00 fault in inovance IS580 drive indicates a Motor Ground Fault. This means the drive ha...

In forum Inovance CP700 – Air compressor & IS580 – Injunction Molding Drive

2 days ago
E21.00 fault in inovance IS580 drive

Cause : EEPROM error comes when function code parameter writing error. This means there is an hardware issue in drive control card. E21.00 fault on the Inovance IS580 drive indicates an EEPROM fault. ...

In forum Inovance CP700 – Air compressor & IS580 – Injunction Molding Drive

2 days ago
E20.00 fault in inovance IS580 drive

Cause : Auto tuning speed feedback fault comes when only during rotating auto-tuning and means the drive couldn't verify motor speed during the test run. E20.00 fault in the Inovance IS580 drive means...

In forum Inovance CP700 – Air compressor & IS580 – Injunction Molding Drive

2 days ago
E19.00 fault in inovance IS580 drive

Cause : Motor auto-tuning fault comes when the motor parameters are not set according to nameplate or motor auto-tuning times out. E19.00 fault in the Inovance IS580 drive indicates a Motor Auto-Tunin...

In forum Inovance CP700 – Air compressor & IS580 – Injunction Molding Drive

2 days ago
E18.00 fault in inovance IS580 drive

Cause : Current sensing fault comes when drive current section circuit is faulty. This fault also comes when the hall is abnormal or the drive board is abnormal. E18.00 fault in inovance IS580 drive i...

In forum Inovance CP700 – Air compressor & IS580 – Injunction Molding Drive

2 days ago
E17.00 fault in inovance IS580 drive

Cause : Pre-charge relay fault comes when hardware issue in drive power card. This means that drive board and power supply are abnormal and the lightning protection board is abnormal. E17.00 fault in ...

In forum Inovance CP700 – Air compressor & IS580 – Injunction Molding Drive

2 days ago
Page 6 / 1331

Click2Electro

Typically replies within minutes

Need any help for fault, alarm, programming, manual ?

Get free chat support...

🟢 Online